1/6 thick film chip resistors mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f da t asheet ? features 1) full line up from ultra small si ze (01005) to 2512 with jumper type. 2) rohm resistors have obtained iso9001/iso/ts16949 certification. packing specification quantity / reel type code 06031005 1608 2012 3216 3225 5025 6432 yrt 15,00010,000 5,0004,000 mrt ert jrt mcr006mcr01 mcr03 mcr10 mcr18 mcr25 mcr50 mcr100 paper tape (4mm pitch) paper tape (2mm pitch) embossed tape (4mm pitch) part no. (mm) size 02010402 0603 0805 1206 1210 2010 2512 (inch) ? part number description 06 mcr (micro chip resistors) 0y t r c mr part no. resistance code, 3 or 4 digits.000 denotes jumper type. ex.) 1 = 1r0 ( 5% ) 9.1 = 9r1 ( 5% ) 10 = 10r0 ( 0.5%, 1% ) 100 ( 5% ) 2.2m = 2204 ( 1% ) 225 ( 5% ) d,f j :: 4 digits3 digits resistance tolerance resistance code 006 (0603 [0201])01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) 25 (3225 [1210]) 50 (5025 [2010]) 100 (6432 [2512]) d ( 0.5% ) f ( 1% ) j ( 5% ) (including jumper type) size (mm [inch]) resistance tolerance nominal resistance j0 10 type code downloaded from: http:///
2/6 da t asheet mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f ? products list ? design and specifications are subject to change without notice. carefully check the specification sheet supplied with the product before using or ordering it. ? rated voltage is determained from the following. when rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage. ? rated voltage = rated power rasistance limiting element voltage (v) temperature coefficient (ppm / c) resistance tolerance (%) operating temperature range ( c ) type code resistance range series part no. rated power (70 c) (w) mcr006 yrt jumper type : rmax = 50m / imax. = 0.5a jumper type : rmax = 50m / imax. = 1a jumper type : rmax = 50m / imax. = 1a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. =2a j( 5%) 2550 50 150200 200 200 200 0.05 mrt ertert ert jrtjrt jrt mcr01mcr03 mcr10 mcr18 mcr25 mcr50 mcr100 0.063 0.1 0.125 0.1 0.125 0.250.25 0.5 1 + 600 / 200 + 500 / 250 250 250 200 100 9.1 10m 10m 1m 9.1 976k 1m 2.2m 10m 9.1 10m 976k 2.2m 9.1 3.3m 1m 91 1m 9.1 560k 180k 9.1 100k 82k 9.1 976k 91 10m 10m 9.1 10m 976k 2.2m 91 1m f( 1%) d( 0.5%) j( 5%) f( 1%) d( 0.5%) j( 5%) f( 1%) j( 5%) f( 1%) j( 5%) j( 5%) j( 5%) f( 1%) f( 1%) f( 1%) j( 5%) f( 1%) 55 to + 125 55 to + 155 55 to + 125 e24 d( 0.5%) 100 50 200 e24 e24,e96 e24e24 e24e24 e24,e96 e24 e24,e96 e24 e24,e96 e24,e96 e24 e24,e96 e24 e24,e96 100 200 100 400 200 100 d( 0.5%) 100 50 400 200 100 d( 0.5%) 100 50 250 100 100 100 100 250 400 100 100 200 1.0 10 10 1k 1.0 10 100 1m 10 1.0 10 10 1m 1.0 10 10 10 100 1.0 10 10 1.0 10 10 1.0 10 10 1m 10 1.0 10 10 1m 10 100 toto to to 910 10 toto to 2.2m 10 toto 91 100 10 to to toto to to 2.2m 10 toto to to to toto to to toto to to toto 10m 10 toto 1m 50 100 to to toto to to 2.2m 10 toto to to downloaded from: http:///
3/6 da t asheet mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f ? chip resistor dimensions and markings there are three or four digits used for the calculation number according to iec code and ris used for the decimal point. part no. type code (mm) (inch) l w t a b marking existence (unit : mm) mcr006 yrt 0603 0201 0.6 0.03 0.3 0.03 0.23 0.03 0.15 0.05 0.15 0.05 no mcr01 mrt 1005 0402 1.0 0.05 0.5 0.05 0.35 0.05 0.2 0.1 no mcr03 ert 1608 0603 1.6 0.1 0.8 0.1 0.45 0.1 0.3 0.2 0.3 0.2 yes ? mcr10 ert 2012 0805 2.0 0.1 1.25 0.1 0.5 0.1 0.35 0.2 0.35 0.2 yes mcr18 ert 3216 1206 3.05 0.15 1.55 0.15 0.55 0.1 0.45 0.25 0.35 0.25 yes mcr25 jrt 3225 1210 3.2 0.15 2.5 0.15 0.55 0.15 0.5 0.25 0.5 0.25 yes mcr50 jrt 5025 2010 5.0 0.15 2.5 0.15 0.55 0.15 0.6 0.25 0.6 0.25 yes mcr100 jrt 6432 2512 6.3 0.15 3.2 0.15 0.55 0.15 0.6 0.25 0.6 0.25 yes 0.25 + 0.05 0.1 m arking method of jumper type jumper type marking existenc e no yes mcr006 / 01 / 25 / 50 / 100 mcr03 / 10 / 18 ? marking method of mcr03 the description of markings on the ch ip resistor are as shown below. marking method (j class): the nominal resistance is expre ssed in by e-24series 3 digits. the first 2 digits apply to the resistance value and the last one indicates the number of zeros to follow. the r is used as a decimal point. example 100k ?? = 104 marking method (f/d class): ? for the resistance value contained in e96 series. the nominal resistance is expressed in 3 digits. the first 2 digits is symbol to the resistance value and the last one is symbol to multipliers. example : 100k ?? = 01d (01d ? 100 10 3 = 100,000 ?? = 100k ? ) example : 3.01k ?? = 47b (47b ? 301 10 1 = 3010 ?? = 3.01k ? ) ? for the resistance value not cont ained in e96 series and contained in e-24 series. the marking is expressed by e-24 se ries in 3 digits and one short bar under the last marking letter. example : 390 ?? = 391 ? land pattern example b d a land c b bb 103 l l w w t t a aa mcr006 / 01 / 03 mcr10 / 18 / 25 / 50 / 100 s ymbol for e96 series nominal resistance value symbol e96 symbol e96 symbol e96 symbol e96 0102 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 100102 105 107 110 113 115 118 121 124 127 130 133 137 140 143 147 150 154 158 162 165 169 174 178182 187 191 196 200 205 210 215 221 226 232 237 243 249 255 261 267 274 280 287 294 301 309 316324 332 340 348 357 365 374 383 392 402 412 422 432 442 453 464 475 487 499 511 523 536 549 562576 590 604 619 634 649 665 681 698 715 732 750 768 787 806 825 845 866 887 909 931 953 976 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 4950 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 7374 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 s ymbol for multipliers symbol a b c d e f x y multipliers 10 0 10 1 10 2 10 3 10 4 10 5 10 1 10 2 dimensions part no. type code a mcr006 mcr01mcr03 mcr10 mcr18 mcr25 mcr50 mcr100 yrt mrt ertert ert jrtjrt jrt 0.30.5 1.0 1.2 2.2 2.2 3.8 5.1 b 0.84 1.32.0 2.6 4.0 4.0 6.0 8.1 c 0.30.5 0.8 1.15 1.52.3 2.3 3.0 d 0.27 0.40.5 0.7 0.9 0.9 1.1 1.5 (unit : mm) downloaded from: http:///
4/6 da t asheet mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f ? derating curve when the ambient temperature e xceeds 70c, power dissipation must be adjust ed according to the derating curves below. 0 20 40 60 80 100 55 0 70 100 125 ambient temperature ( c) percent rated power (%) mcr006 / 100 ? characteristics test items test conditions resistor type guaranteed value jumper type resistancevariation of resistance with temperature solderability damp heat, steady state endurance at 70 c endurance rapid change of temperature bend strength of the end face plating resistance to solvent resistance to soldering heat overload (2.0% + 0.1 ) max. 50m (1.0% + 0.05 ) (3.0% + 0.1 ) max. 50m max. 100m see "products list"see "products list" 20 c no remarkable abnormality on the appearance. a new uniform coating of minimum of95% of the surface being immersed and no soldering damage. without mechanical damage such as breaks. compliance standard(s) : iec60115 8 jisc 5201 8 measurement : + 20 / 55 / + 20 / + 125 c soldering condition : 260 5 c duration of immersion : 10 1s 40 c, 93%rh (relative humidity) test time : 1,000h to 1,048h (3.0% + 0.1 ) (3.0% + 0.1 ) (1.0% + 0.05 ) (1.0% + 0.05 ) (1.0% + 0.05 ) max. 100m max. 100m max. 50m max. 50m max. 50m 70 c rated voltage (current)1.5h : on 0.5h : off test time : 1,000h to 1,048h125 c (mcr006 / 25 / 50 / 100) 155 c (mcr01 / 03 / 10 / 18) test time : 1,000h to 1,048h23 5 c , immersion cleaning, 5 0.5min solvent : 2 propanol test temp. 55 c to + 125 c 100cycle (mcr006) 55 c to + 125 c 300cycle (mcr01) 55 c to + 125 c 5cycle (mcr03 / 10 / 18 / 25 / 50 / 100) rosinethanol : 25% (weight)soldering condition : 235 5 c duration of immersion : 2.0 0.5s test voltage is the smaller one of 1 or 2 1 rated voltage (current) 2.5, 2s. 2 maximum overload voltage m aximum overload voltage ? test voltage mcr006 50v mcr01 100v mcr03 100v mcr10 200v mcr18 400v mcr025 400v mcr50 400v mcr100 400v mcr01 / 03 / 10 / 18 / 25 / 50 0 20 40 60 80 100 55 0 70 100 155 ambient temperature ( c) percent rated power (%) downloaded from: http:///
5/6 da t asheet mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f ? tape dimensions 0.38 0.03 0.68 0.03 0.7 0.1 1.2 0.1 1.0 0.1 1.8 0.1 1.55 0.1 2.3 0.1 1.9 0.2 3.5 0.2 (unit : mm ) w type code part no. f e a 0 b 0 8.0 0.2 mcr006 yrt 3.5 0.05 1.75 0.1 8.0 0.3 mcr01 mrt 3.5 0.05 1.75 0.1 8.0 0.3 mcr03 ert 3.5 0.05 1.75 0.1 8.0 0.3 mcr10 ert 3.5 0.05 1.75 0.1 8.0 0.3 mcr18 ert 3.5 0.05 1.75 0.1 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 max 0.5 2.0 0.05 2.0 0.05 2.0 0.05 2.0 0.05 max 1.1max 1.1 max 1.1 max 1.1 d 0 type code part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 mcr006 yrt 2.0 0.05 mcr01 mrt 2.0 0.1 mcr03 ert 4.0 0.1 mcr10 ert 4.0 0.1 mcr18 ert 4.0 0.1 2.8 0.2 3.5 0.2 8.0 0.2 mcr25 jrt 3.5 0.05 1.75 0.1 1.5 + 0.1 0 2.0 0.05 max 1.1 4.0 0.05 mcr25 jrt 4.0 0.1 3.0 0.1 3.5 0.1 3.4 0.2 5.6 0.2 3.5 0.2 6.7 0.2 (unit : mm ) w type code part no. f e a 0 b 0 8.0 0.3 mcr25 jrt 3.5 0.05 1.75 0.1 12 0.3 mcr50 jrt 5.5 0.05 1.75 0.1 12 0.3 mcr100 jrt 5.5 0.05 1.75 0.1 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 max 1.1 2.0 0.05 2.0 0.05 max 1.1max 1.1 d 0 type code part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 4.0 0.1 mcr25 jrt 4.0 0.1 mcr50 jrt 4.0 0.1 mcr100 jrt 4.0 0.1 ? embossed tape a 0 p 1 p 0 p 2 b 0 f w t 2 e d 0 ? paper tape p 0 p 2 p 1 e f w t 2 d 0 a 0 b 0 b ase paper (bottom tape) components cavity top tape downloaded from: http:///
6/6 da t asheet mcr series < not for automotive application > www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2015.02 - rev.f ? reel dimensions 0 2 0 4 0 6 0 8 0 2 0 4 0 6 0 8 c abd label according to eiaj et-7200b a type code part no. b c d (unit : mm ) 13 0.2 180 0 1.5 60 + 1.0 0 mcr006 yrt mcr01 mrt mcr03 ert mcr10 ert mcr18 ert mcr25 jrt mcr50 jrt mcr100 jrt 9 + 1.0 0 13 + 1.0 0 downloaded from: http:///
r1102 a www.rohm.com ? 2015 rohm co., ltd. all rights reserved. notice ro hm cu stome r s upport sy s tem h ttp :// www.r oh m .co m/ co n tact / thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. no tes the information contained herein is subject to change without notice. before you use our products, pl ease contact our sales representative and verify th e la tes t specifica - tion s : alt hou gh rohm is contin uous ly wor ki ng to im pr ove p ro du ct r eli a bility and qualit y, semicon - du c tor s c an bre a k d ow n and ma lf un ct io n du e to var io us f ac to rs. th e re fore, in or der to prevent pe r so nal in ju ry or fi re ar isi ng f ro m fa ilur e, please ta ke sa f ety mea s ur es su ch as com plyin g wi th th e de r at in g ch ara ct er ist ic s, impl e menting redundant and f ir e preve nt ion designs, and u tilizin g ba ck up s a nd f ail - sa fe p ro ce du re s. ro hm shall have no responsibility for any damages arising out of the use of our poducts b ey ond the rating specified by rohm. examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not gr ant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm or any other parties. rohm shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. the products are intended for use in general electronic equipment (i.e. av/oa devices, communi- cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. the products specified in this document are not designed to be radiation tolerant. for use of our products in applications requiring a high degree of reliability (as ex emplified bel ow), please contact and consult with a rohm representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. do not use our products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. rohm shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. rohm has used reasonable care to ensur the accuracy of the information contained in this document. however, rohm does not warrants that such information is error-free, and rohm shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. please use the products in accordance with any applicable environmental laws and regulations, such as the rohs directive. for more details, including rohs compatibility, please contact a rohm sales office. rohm shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. when providing our products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the us export administration regulations and the foreign exchange and foreign trade act. this document, in part or in whole, may not be reprinted or reproduced without prior consent of rohm. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10)11) 12) 13) 14) downloaded from: http:///
|
